For attaching asphalt shingles to standard decking, nails can range in length from 1 inch to 2 inches. But some applications may require longer nails up to 6 inches long. Those longer nails aren’t likely to be needed for residential roofing, and, as a result, are difficult to find in local roofing supply stores.
What size nails should I use for second layer of shingles?
You should use one-quarter-inch nails for a standard-thickness shingle, and one-half-inch nails for special-thick shingles.
Do you use 4 or 5 nails per shingle?
Four nails per shingle is widely accepted as the industry standard, but warranty requirements and building codes may call for more.
What kind of nail gun for shingles?
Pneumatic nail guns are the most popular type for roofers. A nailer that accommodates 3/4 – 1-3/4 inch nails is ideal.
What length of nail for asphalt shingles Related Questions
Can I use 1 inch nails for shingles?
If you’re using typical architectural shingles and 3/8-inch-thick sheathing, you’ll need 1‚Äêinch nails. If your building codes require thicker sheathing, you’ll need 1 ¬º-inch nails. When installing thicker shingles, you may need to use a longer nail in order to penetrate the OSB beneath fully.
Are 2 inch roofing nails too long?
Typically, a roofing nail measures anywhere from 1 to 2 inches. A roofing nail should be long enough to penetrate the shingle and then as the plywood or OSB decking beneath by at least 3/4 of an inch. The sheathing thickness can vary, so you may need longer nails depending on the decking used.
What size roofing nails are recommended?
The International Building Code requires that roofing nails have a minimum 12-gauge shank and a 3/8-inch diameter head.
Is 2 layers of shingles OK?
As mentioned above, homeowners are legally limited to two layer of roof shingles. Therefore, if you already have two layers, you’ll need a full tear-off. Additionally, if your roof is severely damaged, it likely won’t be able to support the weight of a reroof and will need to be torn off.
What is the normal length of roofing nails?
The standard dimensions for roofing nails are gauge (diameter) and length. Roofing nails are usually somewhere between 1 to 2 inches long, while the gauge is often between 10 and 12.
Is hand nailing shingles better?
Roofing manufacturers have determined that hand-nailing shingles and using a nail gun are both valid methods of installing shingles, so it is not a reflection on your roofer’s work quality level if they choose one over the other.
How many nails do I need to shingle my roof?
Generally, you should use four nails per shingle in the field of the roof, and 5 nails per starter shingle. For regular three-tab shingles, this would require 320 nails per square for field shingles.
Can I use brad nails for shingles?
Though typically used for jobs like molding, brad nails can work well with wood shingles. The Ryobi P320 Airstrike 18V One+ Lithium-Ion Cordless Brad Nailer can deliver as many as 700 nails per charge. It has easy depth adjustment, with an onboard dialer to set the preferred depth.
Can you use roofing nailer for shingles?
The difference is in the detail. Roofing guns are built to drive nails that are appropriate for most types of asphalt and fiberglass shingles, waterproof tar paper and insulation board. Whether you are installing a new roof, or re-roofing, roofing nailers are built specifically for what they are named.
How thick is a shingle?
A standard three-tab shingle is only about 3/16-inch thick. When installed, however, they overlap, doubling the thickness. Wood, cedar shake, and tile are thicker, depending upon the brand of shingles you select. Metal roofing is thinner, corrugated or standing seam, which increases its height by 1 to 2 inches.
What is the shortest shingle nails?
The shortest roofing nail available is around a three-quarters inches long. However, when using this particular size, it’s essential to fully overlap each piece of material and use additional fasteners along the edges to create a weathertight seal.
Can I nail down loose shingles?
Position the pry bar on top of the loose shingle and grab each lifted nail. Push on the pry bar or hit it with a hammer to pull the nail out completely. Repeat this process with each shingle. Nails going through the row of undamaged shingles above the loose ones should be securing the lower row as well.
Should roofing nails come through plywood?
Nails should be long enough to penetrate all layers of roofing materials and achieve secure anchorage into a roof deck. Nails should extend at least 1/8 of an inch through the underside of plywood or other acceptable wood panel decks less than 3/4 of an inch thick.
What size nail do I need?
Eight-penny or 16-penny? The accepted rule of thumb is the nail length should be 21/2 times the thickness of the wood you are nailing through. Thus, for 1-inch-thick material, you would use an 8-penny nail and for 2-inch-thick material, you’d use a 16-penny nail.
What nails are used in steel roofing?
Different roofing materials require different types of roofing nails. Aluminum nails are good for metal roofs and shingles, but they are not recommended for areas where they can be exposed to chemicals or salt. If you live in a coastal area, use stainless steel roofing nails.
Is a roofing nail the same as a regular nail?
The main difference between the two nails is that roofing nails are designed to come out, unlike the siding nail, which is meant to be secured into the siding for its lifetime. Roofing nails will need replacing every so often, so the design of the larger nail head allows for an easier grab for removal.