If you’re using typical architectural shingles and 3/8-inch-thick sheathing, you’ll need 1‚Äêinch nails. If your building codes require thicker sheathing, you’ll need 1 ¬º-inch nails. When installing thicker shingles, you may need to use a longer nail in order to penetrate the OSB beneath fully.
What length roofing nails should I use?
Typically, a roofing nail measures anywhere from 1 to 2 inches. A roofing nail should be long enough to penetrate the shingle and then as the plywood or OSB decking beneath by at least 3/4 of an inch. The sheathing thickness can vary, so you may need longer nails depending on the decking used.
What size nails should I use for second layer of shingles?
You should use one-quarter-inch nails for a standard-thickness shingle, and one-half-inch nails for special-thick shingles.
What length of nail for asphalt shingles?
For attaching asphalt shingles to standard decking, nails can range in length from 1 inch to 2 inches. But some applications may require longer nails up to 6 inches long. Those longer nails aren’t likely to be needed for residential roofing, and, as a result, are difficult to find in local roofing supply stores.
What size roofing nails to use on shingles Related Questions
Do you use 4 or 5 nails per shingle?
Four nails per shingle is widely accepted as the industry standard, but warranty requirements and building codes may call for more.
What are 7 8 roofing nails used for?
Manufactured for quick and easy installation, hot-dipped galvanized roofing nails are ideal for attaching roof shingles, insulation board, and felt-to-wood framing. The large, Flat Head provides a large bearing surface and strong holding power for a secure finish.
Is it better to hand nail shingles?
What Does the Shingle Manufacturer Say? Roofing manufacturers have determined that hand-nailing shingles and using a nail gun are both valid methods of installing shingles, so it is not a reflection on your roofer’s work quality level if they choose one over the other.
Why do roofers use long nails?
If you have additional layers on your roof, as is the case with a roofing overlay, nails should be long enough to penetrate all the way through the roofing material to the roof deck. The nail length varies depending on the material of extra roof layering, but a roofer could use a nail as long as 2-inches or more.
Do you nail or staple roofing felt?
Some roofers prefer to attach felt underlayment with one-inch roofing nails ,or special nails with plastic washers, but most codes allow staples, which are easier to drive.
How many pounds of nails do I need for a bundle of shingles?
You will need approximately 2 ¼ pounds of nails to install a square of shingles in regular conditions, and about 3 ½ pounds if you are dealing with windy conditions. Because nails are purchased by the pound, so can ask your supplier for the correct number of nails for your size roof, in the length you specify.
How many nails do I need for 2 squares of shingles?
Generally, you should use four nails per shingle in the field of the roof, and 5 nails per starter shingle. For regular three-tab shingles, this would require 320 nails per square for field shingles.
How many rolls of nails per square of shingles?
Generally, you should use four nails per shingle. For regular three-tab shingles, this would require 320 nails per square. For high wind areas or when shingles are being applied to a mansard, six nails per shingle are required (480 nails per square).
How far should roofing nails penetrate?
Nails should be long enough to penetrate 3/4 of an inch into a roof deck; if a roof deck is less than 3/4 of an inch, nails should be long enough to penetrate and extend at least 1/8 of an inch through the roof deck.
Are 4 nails required for fastening each shingle?
To prevent damage to shingles during application, they must be sufficiently warm to allow proper forming. IMPORTANT: Use two nails to fasten each shingle. Nails must be minimum 13‚ÅÑ4″ (45 mm) long.
Do you use nails or staples for shingles?
Roofing nails are highly preferred to staples for asphalt and other types of roofs because they offer more holding power, meet building codes, and are easier to install correctly.
What is the most common roofing nail?
The most common types of roofing nails are made from aluminum, stainless steel, galvanized steel, and copper. We do not recommend all of these types, but that doesn’t stop some contractors from using them.
What are 2 and 3 8 nails used for?
Most commonly used in framing and construction work, these nails are perfect for exterior carpentry projects.
What is an 8 inch nail used for?
National Nail Corp 53265 Smooth Shank Bright Spike Nails 8″ x 3/8″ 5LB are 8 inches long and 3/8″ in diameter. Primary applications include securing railroad ties, landscaping timbers and thick members used in log home construction.
What causes roofing nails to pop through shingles?
When the temperature changes, expansion and contraction can cause the nails to pop up and lift the shingles. You should also make sure your roof is adequately ventilated. Other causes of nail pops can be that the shingles were not nailed tightly when the roof was installed.
Can I staple my roof shingles?
Fastener Type The type of fastener used to fasten the shingles is especially important in resisting wind uplift and pull-through. Fasteners for asphalt shingles should be roofing nails or staples. The head of a roofing nail or the crown of a staple is what actually holds a shingle in place.