You do need to use a starter course with architectural shingles. The starter edge will help seal the edges and cover your shingle joints. As it won’t be visible on the finished roof, you don’t need to worry about the look of your starter strip and whether it matches your architectural shingles.
What is the purpose of starter shingles on a roof?
A shingle starter strip is an important part of a residential roofing system. It plays a critical role in reducing the risk of shingle blow-off along the eaves and rakes of the roof. It provides a base under the shingle at the eaves, helping the roof shed water efficiently.
How many starter shingles in a bundle?
Starter Strip is packaged two pieces per shingle, 16 shingles per bundle, 100 lineal feet, and perforated down the center allowing for easy separation.
How are starter shingles different?
Starter shingles are used at the bottom edge of your roof, while ridge shingles are used at the peak. Starter shingles have a shallow “cut” or “notch” so they lay flat against the roof decking, while ridge shingles have a deep “cut” or “notch” to allow for proper ventilation at the peak of your roof.
Do you need to install starter shingles Related Questions
How many feet do starter shingles cover?
Starter Strip shingle is designed to be broken into two pieces, and each piece has its own sealant strip. When separated, each starter shingle is 65 ‚ÅÑ8″ x 393 ‚ÅÑ8″, and each bundle will cover approximately 105 lineal feet.
Where do you put starter on a roof?
Starter shingle should be installed around ALL edges of your roof. To meet code, technically it only needs to be installed on the bottom eaves, but there are some big benefits to installing it up the rake edges as well (also known as gable edges).
How long to cut starter shingles?
Cut 12 inches (30.4 centimeters) off the length of the first shingle that you lay. Then lay down whole tiles to the end of the row, trimming the last shingle so that it fits correctly. Continue laying and nailing down shingles in this manner.
Are starter shingles visible?
Laying Down Starter Shingles Despite being such an important part of the roof, Starter Strip Shingles aren’t ‚Äì or shouldn’t be ‚Äì visible in the final roof. They’re meant to be installed under the first row of roof shingles, surrounding the perimeter of the roof.
How do you tell if shingles are installed correctly?
Check the shingles for proper nailing or overhang. When correctly installed, the edges of your shingles will hang over a roof around 1” — 1 ½”, or about ½” — ¾” for drip edge flashing. If you have excess, then shingles can blow off with too much wind.
Do roof shingles need glue?
One of the most important parts of a proper asphalt roof shingle installation is proper adhesive bonding. Adhesive strips are present on all asphalt shingles and help each shingle to stay in place with the shingles around it.
How many starter shingles do I need?
Roof surfaces are measured in “squares”. A roofing square is equal to 100 square feet of the roof. To determine the number of squares on the gable roof example in this post, divide its total of 2400 square feet by 100 (2400 ÷ 100 = 24). This means you would need 24 squares of shingles to cover that roof.
Are starter shingles waterproof?
Not only does ShingleStarter provide the necessary waterproofing protection, but it also eliminates all the costs associated with cutting shingle tabs for the starter course.
What happens if shingles are incorrectly installed?
Installing shingles too high or too low compared to the previous course can affect the exposure, which in turn would affect the aesthetics, wind performance and seal strength of the roof. An improperly aligned shingle course would be very noticeable and have a wavy appearance that is unattractive and amateurish.
Do you need starter strip?
The starter strip is crucial because it adheres to the shingles on the edges of your roof and protects them from the elements. Without starter strip shingles, a gust of wind would have no trouble sneaking under the shingles on the edges of your roof and blowing them up, and perhaps even off, your roof.
What is starter strip siding?
The PlyGem Vinyl Starter Strip is a required accessory to start any vinyl siding installation job. Starter Strips are used at the bottom of each wall of the home and must be level. This is done to lock the first course of siding in place.
How wide are starter shingles?
IB-3‚Ñ¢ ShingleStarter‚Ñ¢ is a 36″ wide self-adhering mineral surface starter shingle that serves the dual function of replacing the coventional starter strips, as well as serving as an ice and water dam in cold climates.
Can you use regular shingles for starter?
The starter strip is the layer of shingles underneath the first course along the edge of the roof. Some roofers simply take regular shingles, flip them upside down and nail them down as a starter course.
How many starter shingles per square?
Three bundles to a square is most common, which applies to most three-tab strip shingles and some lightweight laminated shingles. Heavier three-tabbed shingles and laminated shingles require four, or sometimes five, bundles to cover a square.
Which roof to shingle first?
The application guide on the shingle wrapper states that the smaller roof should be shingled first, running the shingles through the valley. The main roof shingles are then applied over the dormer shingles and are to be cut 2″ back from the valley centerline.
What is the distance between shingles?
Spacing between shingles in the same course should be ¼-inch to ⅜-inch. Flat-grain shingles wider than 8 inches should be split in two before installation. Modern building codes require that no two joints in any three adjacent courses be in alignment.