One of these materials is starter shingle. Starter shingle should be installed around ALL edges of your roof. To meet code, technically it only needs to be installed on the bottom eaves, but there are some big benefits to installing it up the rake edges as well (also known as gable edges).
What is the purpose of starter shingles on a roof?
A shingle starter strip is an important part of a residential roofing system. It plays a critical role in reducing the risk of shingle blow-off along the eaves and rakes of the roof. It provides a base under the shingle at the eaves, helping the roof shed water efficiently.
Do you need starter shingles on the rake?
The starter shingle’s two purposes are water protection and wind protection at the eave and rake. A starter shingle is used to seal with the field shingle at the first course along the eave and rake. This helps prevent wind and water from getting beneath the shingle in this critical location.
How far should starter shingles hang over drip edge?
How Should Shingles Be Installed Over Drip Edge? Shingles should be installed over the drip edge a minimum of 3/8” (9 mm) at both the eave edge and the rake edge. If the drip edge extends… out from the rakes and eaves (typically called DL Style or D Type), the shingles may be installed flush with the drip edge.
Do you put starter shingles up the side of a roof Related Questions
Do you need starter strip on gable ends?
The starter strip is crucial because it adheres to the shingles on the edges of your roof and protects them from the elements. Without starter strip shingles, a gust of wind would have no trouble sneaking under the shingles on the edges of your roof and blowing them up, and perhaps even off, your roof.
How many starter shingles do I need?
Roof surfaces are measured in “squares”. A roofing square is equal to 100 square feet of the roof. To determine the number of squares on the gable roof example in this post, divide its total of 2400 square feet by 100 (2400 ÷ 100 = 24). This means you would need 24 squares of shingles to cover that roof.
Should you use starter shingles and drip edge?
We don’t recommend installing a drip edge after your starter shingles. In fact, the proper order to follow should be your drip edge first, along with an underlayment such as an ice and water shield. Roofing felt should also go before installing starter shingles.
What is the difference between shingles and starter shingles?
Starter shingles are used at the bottom edge of your roof, while ridge shingles are used at the peak. Starter shingles have a shallow “cut” or “notch” so they lay flat against the roof decking, while ridge shingles have a deep “cut” or “notch” to allow for proper ventilation at the peak of your roof.
Does starter strip go on eaves and rakes?
Where Do Starter Shingles Go On A Roof? Starter shingle strips are installed at the rakes, eaves, and ridges. However, some may debate that rakes don’t need starter shingles as those areas may not be prone to wind damage. There are many more functions of starter shingles that every homeowner should know.
Can you use upside down shingles as starter?
Some roofers simply take regular shingles, flip them upside down and nail them down as a starter course. The problem with this approach is that it doesn’t allow for proper adhesion between the starter course and the first layer of shingles.
Does flashing go over or under shingles?
Flashing should overlap the roof-covering material, but on asphalt shingle roofs, for aesthetic reasons, the part of the headwall flashing that extends down over asphalt shingles is often covered with a course of shingle tabs.
Does drip edge go over or under roll roofing?
It is also a good idea to install drip edge flashing before laying the rolled roof. Drip edge is a type of metal flashing that is installed at the edges of your roof to keep water from getting underneath your roofing materials.
Do I need drip edge on all sides of roof?
In short, yes, it’s necessary to have drip edge installed on your roof. Without the installation of drip edge flashing on your roof, water could get behind the gutter and start running down your home. This would allow for moisture to collect on the fascia board causing it to rot.
Can you install shingles without starter strip?
You do need to use a starter course with architectural shingles. The starter edge will help seal the edges and cover your shingle joints. As it won’t be visible on the finished roof, you don’t need to worry about the look of your starter strip and whether it matches your architectural shingles.
What length do you cut starter shingles?
Cut 12 inches (30.4 centimeters) off the length of the first shingle that you lay. Then lay down whole tiles to the end of the row, trimming the last shingle so that it fits correctly. Continue laying and nailing down shingles in this manner.
How far does a bundle of starter go?
Starter Strip shingle is designed to be broken into two pieces, and each piece has its own sealant strip. When separated, each starter shingle is 65 ‚ÅÑ8″ x 393 ‚ÅÑ8″, and each bundle will cover approximately 105 lineal feet.
Where does the drip edge go on a roof?
The correct placement of a roof drip edge is on top of the roof’s exterior cover directly between the sheathing and the fascia board, which forms a drainage gap between the drip edge and the fascia board. As a result, the drainage improves water flow and protects the roof from potential water damage.
How many starter shingles in a bundle?
Starter Strip is packaged two pieces per shingle, 16 shingles per bundle, 100 lineal feet, and perforated down the center allowing for easy separation.
Do starter shingles come in a bundle?
Starter strip shingles are packaged 2-pieces per shingle, 16 shingles per bundle, 100 lin.
Does drip edge only go on eaves?
It’s important to understand that drip edge installation is different for eaves and rakes. After your roof deck has been prepared, and before you install underlayment, you need to install drip edges at the eaves. You install drip edges on the rakes after you install the underlayment.